Corporate Headquarters:Copyright © 2003 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

10Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Traffic ManagementThe VIP6-80 supports the following:• Simple

11Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01• Cisco 7000 series routers with the 7000 Series Route Switch

12Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Safety WarningsSafety warnings appear throughout this publicat

13Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Electrical Equipment GuidelinesFollow these basic guidelines w

14Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Preventing Electrostatic Discharge DamageElectrostatic dischar

15Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Guidelines for Removal and InstallationThis section describes

16Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Figure 2 Handling Interface Processors—Vertical Orientation Sh

17Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Figure 3 shows a detail of the ejector lever mechanism on the

18Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Removing a VIP6-80This section describes the procedure for rem

19Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Step 5 Place the removed board on an antistatic mat or foam pa

2Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01• Guidelines for Removal and Installation, page 15• Removing a

20Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Figure 4 Handling a Port AdapterSingle-Width Port AdapterSingl

21Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Figure 5 Removing and Installing a Single-Width Port AdapterNo

22Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Dual-Width Port AdapterDual-width port adapters occupy both po

23Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Figure 7 Removing and Installing a Dual-Width Port Adapter Not

24Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Connecting Cables to the Port AdapterRefer to the Installation

25Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Step 6 Using your thumbs, simultaneously push both ejector lev

26Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Checking the VIP6-80 InstallationThis section describes the pr

27Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01%LINK-5-CHANGED: Interface GigabitEthernet3/0/0, changed state

28Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Step 9 Repeat Step 1 through Step 8 to verify that any additio

29Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Using show Commands to Display Interface InformationThis secti

3Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01–Regulatory Compliance and Safety Information for the Cisco 750

30Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01To display hardware information about a specific interface on

31Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01 EEPROM format version 1 VIP6 RM7000B controller

32Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Following is an example of a successful ping command to a remo

33Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Note In the output display of the show diag command (see page

34Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Removing SDRAM DIMMsUse the following procedure to remove the

35Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Step 8 Repeat Step 4 through Step 7 for the remaining DIMM, if

36Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Checking the VIP6-80 Memory UpgradeThis section describes how

37Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01• Remove and reinstall the port adapters. See the “Removing an

38Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Documentation FeedbackYou can submit comments electronically o

39Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01To open a case by telephone, use one of the following numbers:

4Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01The VIP6-80 installs in any of the following interface processo

40Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01• Internet Protocol Journal is a quarterly journal published b

5Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Figure 1 VIP6-80CPUMemory ComponentsYou can use any combination

6Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01LEDsThe VIP6-80 has LEDs; however, they are not be visible once

7Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01The VIP6-80 ROM monitor functions similarly to the boot loader

8Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01PA-2FE-FX Dual-Port Fast Ethernet 100BaseFX 2 SinglePA-4E Ethe

9Versatile Interface Processor (VIP6-80) Installation and Configuration GuideOL-5078-01Note All interface processors are dual-width.For more informati