Cisco 3020 Guia de Instalação

GETTING STARTED GUIDECisco Catalyst Blade Switch 3000 Series for HPGetting Started Guide1 About This Guide2 Taking Out What You Need3 HP Blade System

10 Follow these steps to install the switch module in the blade enclosure. The illustrations in this section show the Cisco Catalyst Blade Switch 3020

11 Step 4 Ensure that the release latch on the switch module is in the open position (perpendicular to the module):Step 5 Slide the switch module into

12 Step 6 Push the release latch on the front of the switch module to the closed position. 5 Using the Onboard Administrator to Assign an IP Address

13 Step 4 Using a PC that is connected to the same network segment as the blade enclosure Onboard Administrator, access the Onboard Administrator in a

14 Figure 6 Express Setup Page for the Cisco Catalyst Blade Switch 3120 for HPFigure 7 Express Setup Page for the Cisco Catalyst Blade Switch 3020 for

15 Using Express SetupBefore you complete the setup program, obtain the default gateway IP address and the switch password from your system administra

16 Figure 8 Advanced Settings Tab Step 2 In the Host Name field, enter a name for the switch module. The host name is limited to 31 characters; embedd

17 Step 9 If you enable SNMP, you must enter a community string in the SNMP Read Community field, the SNMP Write Community field, or both. SNMP commun

18 Step 6 Enter end.Step 7 Enter copy running-configuration startup-configuration to save this setting.Step 8 At the prompt, press Return. Step 9 To v

19 Figure 9 Device Manager Page for the Cisco Catalyst Blade Switch 3120 for HP

2 1 About This GuideThis guide provides instructions on how to install your Cisco Catalyst Blade Switch 3120 for HP or Cisco Catalyst Blade Switch 30

20 Figure 10 Device Manager Page for the Cisco Catalyst Blade Switch 3020 for HPStep 3 Use the device manager to perform basic switch module configura

21 Step 3 Configure the PC terminal emulation software for:– 9600 baud– 8 data bits– No parity– 1 stop bit– No flow controlStep 4 Use the CLI to enter

22 Caution The Cisco Catalyst Blade Switch 3120 for HP switch modules do not support switch stacks with other types of blades switches as members. Com

23 To create a switch stack:Step 1 Install the member switch modules if you have not already done so.Step 2 Connect the StackWise Plus cables as descr

24 Figure 11 Inserting the StackWise Plus CablesWhen you remove the StackWise Plus cables from the connectors, replace the dust covers to protect them

25 For simplified cabling, the automatic medium-dependent interface crossover (auto-MDIX) feature is enabled by default on the switch. With auto-MDIX

26 be turned on, there might be a cable problem, or there might be a problem with the adapter installed in the device. See the “In Case of Difficulty”

27 For More InformationFor more information about the switch module, see these documents on Cisco.com:• Cisco Catalyst Blade Switch 3120 for HP Hardwa

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0

3 Shipping Box ContentsCisco Switch Module DescriptionsThese sections describe the switch modules:• Cisco Catalyst Blade Switch 3120 for HP, page 3• C

4 The Cisco Catalyst Blade Switch 3120 for HP has a 3120G and a 3120X model. Both are stacking-capable. The initial setup procedure for both models is

5 Table 1 describes the Cisco Catalyst Blade Switch 3120 for HP switch module ports. Each external port has an associated LED.Cisco Catalyst Blade Swi

6 Figure 2 shows the Cisco Catalyst Blade Switch 3020 for HP switch module. Each external port has an associated LED.Figure 2 The Catalyst Blade Switc

7 Table 2 describes the switch module ports. Each external port has an associated LED.Table 2 Cisco Catalyst Blade Switch 3020 for HP Port Description

8 3 HP Blade System ArchitectureFigure 3 shows the rear view of the blade enclosure, in which you install the switch module.Figure 3 Rear View of the

9 Consider these prerequisites before you install the switch module:• Fill any unoccupied interconnect bays or any unoccupied power module bays in the