Cisco 10008 Guia de Instalação

Quick Start GuideCisco 10008 Router1 Documentation and Resources2 Preparing for Installation3 Installing the Router4 Connecting Power5 Connecting Cabl

10Rack-Mounting the Router in a 19-Inch 4-Post RackUse the following procedure to rack-mount the Cisco 10008 chassis in a 19-inch 4-post rack: Figure

11Rack-Mounting the Router in a 19-Inch 2-Post RackUse the following procedure to rack-mount the Cisco 10008 chassis in a 19-inch 2-post rack: Figure

12Figure 4 Attaching the Chassis to a 19-Inch 2-Post Rack WarningAt least three people are required to mount the chassis in the equipment rack: two pe

13Rack-Mounting the Router in a 23-Inch 2-Post RackUse the following procedure to rack-mount the Cisco 10008 chassis in a 23-inch 2-Post rack:Figure 5

14Figure 6 Attaching 23-Inch 2-Post Rack Bracket AdaptersStep 2 Attach the optional 23-inch adapters to the mounting brackets.3001413240APROCESSOR ONL

15Figure 7 Attaching the Chassis to a 23-Inch 2-Post RackWarningAt least three people are required to mount the chassis in the equipment rack: two peo

16Attaching the Cable-Management BracketUse the following procedure to attach the cable-management bracket to the Cisco 10008 chassis:Figure 8 Attachi

17Attaching the Grounding LugUse the procedure in this section to attach the grounding lug:Before attaching the grounding lug, make sure:• The ejector

18Figure 10 Connecting the Grounding Lug to the ChassisWarningNever defeat the ground conductor or operate the equipment in the absence of a suitably

194 Connecting PowerUse this section for information about connecting power to the Cisco 10008 router.• If you are connecting DC power to the system,

21 Documentation and ResourcesThis section contains information to help you prepare for installing the Cisco 10008 router. It contains a list of onli

20Be sure you have connected the chassis to an earth ground as instructed in the “Attaching the Grounding Lug” section on page 17, and then use the fo

21Figure 12 Removing the Safety CoverStep 2 Loosen the captive screw on the rear safety cover and tilt the cover back to lift it up and out from the c

22Figure 14 DC Power ConnectionsStep 4 Connect the DC power lead from the first external power source to the DC terminal block A labeled –48V.Step 5 C

23Figure 15 Securing DC Power Cables to the ChassisStep 8 Secure the power cabling to the chassis by feeding a tie wrap through the slot on the safety

24Be sure you have connected the chassis to an earth ground as instructed in the “Attaching the Grounding Lug” section on page 17, and then use the fo

25Figure 17 AC Power Cord Connectors in Strain-Relief DevicesStep 3 Set the AC power cord connectors in a power cord strain-relief device to prevent t

265 Connecting CablesThis section provides information about connecting cables to the Cisco 10008 router.Connecting Alarm IndicatorsThe Cisco 10008 r

27Figure 19 Removing the Safety CoverStep 2 Remove the safety cover by lifting it up and out from the chassis.Figure 20 Stripping InsulationStep 3 Usi

28Figure 21 Alarm Indicator Terminal Block ConnectionsStep 4 Connect one set of alarm indicator wires to the alarm terminal block as follows:a. Connec

29Figure 22 Alarm Indicator Wires Exiting the Safety CoverStep 6 Secure the power cabling to the chassis by feeding a tie wrap through the slot in the

3You can access the Cisco website at this URL:http://www.cisco.comYou can access international Cisco websites at this URL:http://www.cisco.com/public/

30Use the following procedure to connect a video terminal to the console port on a PRE:Figure 23 Console Port Connection on the PREStep 1 Connect one

31Connecting Network Management and Signal System CablesThe Cisco 10008 router has connections to both the internal Ethernet management network and th

32Follow these steps to connect the PRE to a 10BASE-T Ethernet LAN:Figure 25 Connecting the 10BASE-T Cable to the Ethernet PortStep 1 Connect one end

33The RJ-45 port on the PRE is configurable for 100-Mbps full-duplex or half-duplex operation (half-duplex is the default) and supports IEEE 802.3, Et

34Auxiliary Modem ConnectionThis asynchronous EIA/TIA-232 serial port is used to connect a modem to the PRE for remote administrative access. Use the

356 Powering On the SystemWhen all of the interfaces are connected, perform a visual check of all connections, and then check that:• The ejector leve

367 Configuring the Cisco 10008 Router at StartupThis section explains how to create a basic running configuration for your Cisco 10008 router using

37Tip Basic configuration setup is often used as a quick way to achieve network connectivity, allowing you to retrieve a configuration file from a TFT

38After you respond to the SNMP questions, the setup script lists the interfaces., for example:Interfaces that are not okay (OK? = NO) do not have a v

39Step 17 After you complete the configuration dialog, enter global configuration mode and enable IP routing by entering the ip routing command:Router

4Cisco Product Security OverviewCisco provides a free online Security Vulnerability Policy portal at this URL:http://www.cisco.com/en/US/products/prod

408 Formatting Flash Disks and Flash CardsThe Flash disk or Flash card that shipped with your router contains the default Cisco IOS image for booting

419 Managing the File SystemsThis section describes the file systems used on the Cisco 10008 router and provides procedures for performing basic file

42Managing Configuration Files Larger than NVRAMTo maintain a configuration file that exceeds the size of NVRAM (512 KB), you must compress or relocat

43Step 5 Exit global configuration mode.Router(config)# endStep 6 When you finish changing the running configuration, save the new configuration.Route

4410 Troubleshooting Installation ProblemsThis section contains general troubleshooting information to help you solve problems you might encounter du

45Troubleshooting Ethernet ConnectionsIf an Ethernet connection to your Cisco 10008 router fails to work properly, and the corresponding LINK LED is n

46Troubleshooting the Console Port Serial ConnectionIf the terminal connected to the Cisco 10008 console port appears frozen or fails to work properly

47

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

5Cisco Technical Support & Documentation WebsiteThe Cisco Technical Support & Documentation website provides online documents and tools for tr

6Obtaining Additional Publications and InformationInformation about Cisco products, technologies, and network solutions is available from various onli

72 Preparing for InstallationThis section guides you through the process of preparing for your router installation.WarningOnly trained and qualified

83 Installing the RouterThe Cisco 10008 router can be rack-mounted in a 19-inch rack with either a flush-mount or center-mount configuration, or in a

9Lifting the ChassisUse the following procedure to rack-mount the Cisco 10008 chassis:Figure 1 Lifting the ChassisWarningAt least three people are req