Cisco 6260 Guia de Instalação Página 173
- Página / 244
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
6-7
Cisco 6260 Hardware Installation Guide
OL-2365-02
Chapter 6 Upgrading and Maintaining the Cisco 6260 System
Installing and Replacing Hardware
6.3.1 xTU-C Line Card
The following sections describe how to remove and replace or install an xTU-C line card.
6.3.1.1 Installing an xTU-C Line Card
Complete the following steps to install the xTU-C line card in the chassis.
Note It is important that you complete each step before moving on to the next step.
Step 1 Connect a grounding strap to the ESD grounding jack that is located on the top right of the Cisco 6260
card cage.
Step 2 Hold the xTU-C line card vertically, with the line card faceplate toward you and the connectors facing
the chassis slot.
Step 3 Align the upper and lower edges of the xTU-C line card with the upper and lower guides in the
chassis slot.
Step 4 Lift up on the ejector lever and gently apply pressure to the bottom of the faceplate while pushing the
line card into the slot.
- Text Part Number: OL-2365-02 1
- CONTENTS 3
- Contents 4
- 5 Troubleshooting 5-1 6
- OL-2365-02 10
- Audience 13
- Organization 13
- Conventions 14
- Related Documentation 15
- Obtaining Documentation 16
- Cisco.com 17
- Technical Assistance Center 17
- Contacting TAC by Telephone 18
- Product Overview 19
- 1.1.1 Features 21
- 1.1.2 Configurations 21
- 1.1.2.3 IMA Configuration 22
- Subtending host 27
- Cisco 6260 System Overview 28
- 1.2.2 Cisco 6260 Connectors 30
- 1.2.3 Cisco 6260 Cards 31
- 1.2.3.1.1 Faceplate Features 32
- 1.2.3.2.1 Faceplate Features 34
- 1.2.3.3.1 Faceplate Features 36
- 1.2.3.4.1 Faceplate Features 38
- 1.2.3.5.1 Faceplate Features 40
- 1.2.3.6.1 Faceplate Features 42
- 1.2.3.7.1 Faceplate Features 44
- NI2-155MM-155MM2 Only 47
- 1.2.3.9.1 Faceplate Features 49
- 1.2.3.13 Redundancy Overview 57
- 1.2.4 Cisco 6260 I/O Modules 59
- Figure 1-19 E3 I/O Module 60
- Figure 1-20 E3 I/O Module 61
- Figure 1-21 OC-3c I/O Module 61
- 1.2.5 PEM 63
- Figure 1-23 PEM Faceplate 64
- 1.2.6 Fan Tray 65
- 1.2.8 ESD Jack 66
- 1.2.7 Air Filters 66
- 1.3 Management Software 67
- Management Software 68
- Preparing for Installation 69
- 2.1.2 Warning Definition 70
- Safety Requirements 71
- 2.1.4.1 Hot Swapping Cards 78
- 2.2 Site Requirements 79
- 2.2.1.2 Ventilation 80
- 2.2.1.3 Space 81
- 2.2.2 Power Requirements 82
- Site Requirements 83
- Required Tools and Equipment 84
- 2.5 Verifying Contents 86
- 2.6 Inspecting for Damage 86
- Inspecting for Damage 87
- 3.1 Installation Checklist 90
- 3.2 Installation Procedures 91
- 3.2.6 Ground the Cisco 6260 95
- Negative connection (–) 101
- Positive connection (+) 101
- Ground connection ( ) 101
- 3.2.12 Apply Power 102
- –48V on the voltmeter 103
- Installation Procedures 108
- 3.2.19.1 Before You Begin 110
- Splitter Configuration 117
- 4.1 Installation Checklist 118
- 4.2 Installation Procedures 118
- Bracket orientation for 120
- ETS 600-mm rack 120
- Bracket orientation 120
- Cisco 6260 122
- 4.2.5 Ground the Cisco 6260 123
- 0.43 in 126
- 4.2.9 Apply Power 129
- 4.2.16.1 Before You Begin 137
- Troubleshooting 145
- 5.2 Basic Checks 146
- 5.4 System-Wide Problems 147
- OL-2365-01 148
- System-Wide Problems 148
- 5.5 FRU-Specific Problems 152
- FRU-Specific Problems 153
- 5.5.3 Line Card Problems 154
- 5.5.4 I/O Module Problems 158
- 5.5.5 Fan Tray Problems 159
- 5.5.6 PEM Problems 160
- 5.6 Alarms 161
- Table 5-17 IMA Group Alarms 164
- Table 5-20 Power Alarms 165
- Cisco 6260 System 167
- 6.2 Fan Tray Maintenance 168
- Fan Tray Maintenance 170
- 6.3.1 xTU-C Line Card 173
- Unlocked 174
- 6.3.2 DS3/2DS3 NI-2 Card 175
- 6.3.4 OC-3c/OC-3c NI-2 Card 181
- 6.3.5 I/O Module 183
- 6.3.6 PEM 186
- 6.3.6.2 Removing the PEM 188
- Technical Specifications 189
- A.1.1 Cisco 6260 Chassis 190
- Hardware Specifications 192
- A.1.9 DS3/2DS3 NI-2 Card 196
- A.1.12 I/O Module 199
- A.1.13 PEM 199
- A.2 Software Specifications 200
- Port Mapping Specifications 201
- Port Mapping Table 202
- Standard Telco Color Chart 206
- C.1 xDSL Connectors 209
- C.2 I/O Module Connectors 209
- • BITS clock input circuits 211
- RJ-45 female 212
- C.5 Ethernet Port 213
- Ethernet Port 214
- Numerics 215
- Glossary 216
Manuais e produtos relacionados com Redes Cisco 6260
Redes Cisco 815 Especificações
(28 páginas)
(28 páginas)
Redes Cisco WES610N Manual do Utilizador
(21 páginas)
(21 páginas)
Redes Cisco 510 Manual do Utilizador
(2 páginas)
(2 páginas)
Redes Cisco 5428 - SN Router Informações Técnicas
(572 páginas)
(572 páginas)
Redes Cisco WPC54GS Guia do Utilizador
(83 páginas)
(83 páginas)
Redes Cisco 10700 Guia do Utilizador
(602 páginas)
(602 páginas)
Redes Cisco ME 3800X Especificações
(622 páginas)
(622 páginas)
Redes Cisco uBR7100 Series Manual do Utilizador
(12 páginas)
(12 páginas)
Redes Cisco 2524 - Router - EN Guia do Utilizador
(30 páginas)
(30 páginas)
Redes Cisco Aironet 340 Series Especificações
(362 páginas)
(362 páginas)
Redes Cisco 867W Manual do Utilizador
(59 páginas)
(59 páginas)
Redes Cisco 1900 series Informações Técnicas
(10 páginas)
(10 páginas)
Redes Cisco 7400 series Guia do Utilizador
(12 páginas)
(12 páginas)
Redes Cisco 7576 Manual do Utilizador
(26 páginas)
(26 páginas)
Redes Cisco WRT610N Manual do Utilizador
(3 páginas)
(3 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais