Cisco Cisco Access Registrar 4.2 Especificações Página 179
- Página / 636
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
4-81
Cisco Wireless LAN Controller Configuration Guide
OL-13826-01
Chapter 4 Configuring Controller SettingsWireless Device Access
Configuring and Viewing Location Settings
Step 4 To verify that the location appliance certificate is installed on the controller, enter this command:
show auth-list
Information similar to the following appears:
Authorize APs against AAA ....................... disabled
Allow APs with Self-Signed Certificate (SSC) .... enabled
Mac Addr Cert Type Key Hash
----------------------- ---------- -------------------------------------------
00:13:80:60:48:3e SSC ecefbb0622ef76c997ac7d73e413ee499e24769e
Synchronizing the Controller and Location Appliance
For controller software release 4.2 or later, if a location appliance (release 3.1 or later) is installed on
your network, the time zone must be set on the controller to ensure proper synchronization between the
two systems. Also, Cisco highly recommends that the time be set for networks that do not have location
appliances. Refer to the “Managing the System Time and Date” section on page 4-6 for instructions on
setting the time and date on the controller.
Note The time zone can be different for the controller and the location appliance, but the time zone delta must
be configured accordingly, based on GMT.
Using the CLI to View Location Settings
The controller determines the location of client devices by gathering received signal strength indicator
(RSSI) measurements from access points all around the client of interest. The controller can obtain
location reports from up to 16 access points for both clients and RFID tags.
Use these commands to view location information using the controller CLI.
1. To view the current location configuration values, enter this command:
show location summary
Information similar to the following appears:
Location Summary :
Algorithm used: Average
Client RSSI expiry timeout: 150 sec, half life: 60 sec
Calibrating Client RSSI expiry timeout: 30 sec, half life: 0 sec
Rogue AP RSSI expiry timeout: 1200 sec, half life: 120 sec
RFID Tag RSSI expiry timeout: 60 sec, half life: 120 sec
- Configuration Guide 1
- CONTENTS 3
- Contents 10
- OL-13826-01 10
- Audience 22
- Organization 22
- Conventions 23
- Related Publications 25
- Overview 27
- Chapter 1 Overview 28
- Single-Controller Deployments 29
- Operating System Software 31
- Operating System Security 31
- Operational Requirements 33
- Configuration Requirements 33
- Controller Platforms 34
- Features Not Supported 35
- Cisco 4400 Series Controllers 36
- Cisco UWN Solution WLANs 40
- Identity Networking 40
- File Transfers 42
- Power over Ethernet 42
- Startup Wizard 43
- Rogue Access Points 47
- • Using the CLI, page 2-7 49
- Guidelines for Using the GUI 50
- Opening the GUI 50
- Using the CLI 55
- Logging Out of the CLI 56
- CLI Interfaces 57
- Controller console 61
- Distribution System Ports 62
- Interfaces 63
- Management Interface 64
- AP-Manager Interface 64
- Virtual Interface 65
- Service-Port Interface 66
- Dynamic Interface 66
- Service-Port Interfaces 68
- Configuring Ports 76
- Configuring Port Mirroring 80
- Enabling Link Aggregation 87
- Link Aggregation Guidelines 89
- Step 3 Reboot the controller 92
- Connecting Additional Ports 98
- Before You Start 100
- Configuring 802.11 Bands 106
- Configuring DHCP Proxy 116
- Configuring RADIUS Settings 117
- Configuring SNMP 118
- Enabling System Logging 124
- Enabling 802.3x Flow Control 124
- Configuring 802.3 Bridging 127
- Configuring Multicast Mode 129
- Configuring Client Roaming 134
- Intra-Controller Roaming 135
- Inter-Controller Roaming 135
- Inter-Subnet Roaming 135
- CCX Layer 2 Client Roaming 136
- Call Admission Control 146
- Expedited Bandwidth Requests 147
- Traffic Stream Metrics 148
- Figure 4-19 Clients Page 152
- (see Figure 4-25) 156
- Configuring EDCA Parameters 162
- Configuring RFID Tag Tracking 173
- General WiSM Guidelines 181
- Configuring the Supervisor 182
- Cisco UWN Solution Security 186
- Layer 3 Solutions 187
- Rogue Access Point Solutions 187
- Configuring TACACS+ 188
- Configuring LDAP 203
- Configuring Local EAP 207
- Figure 5-16 Local EAP Example 208
- Configuring DHCP Option 82 220
- Validating SSIDs 221
- Guidelines for Using MFP 234
- Identity Networking Overview 242
- ACL-Name 243
- Interface-Name 243
- VLAN-Tag 244
- Tunnel Attributes 244
- Configuring AAA Override 245
- Configuring IDS 248
- Viewing Shunned Clients 251
- Configuring IDS Signatures 252
- Configuring AES Key Wrap 260
- WLAN Overview, page 6-2 265
- Configuring WLANs, page 6-2 265
- WLAN Overview 266
- Configuring WLANs 266
- Using the GUI to Create WLANs 267
- Using the CLI to Create WLANs 269
- Configuring DHCP 270
- Security Considerations 271
- Configuring DHCP Scopes 273
- Enabling MAC Filtering 276
- Creating a Local MAC Filter 276
- Assigning WLANs to Interfaces 277
- Configuring Layer 2 Security 280
- WPA1 and WPA2 282
- Configuring a Session Timeout 287
- Configuring Layer 3 Security 288
- VPN Passthrough 289
- Web Authentication 289
- Configuring QoS Enhanced BSS 293
- Configuring IPv6 Bridging 296
- Configuring WLAN Override 301
- Creating Access Point Groups 304
- Configuring the RADIUS Server 307
- External Antenna Connectors 316
- Antenna Sectorization 317
- Wireless Mesh 320
- Configuring Mesh Parameters 324
- MESH MESH 331
- MESH MESH MESH 331
- MESHMESH 331
- Figure 7-10 All APs Page 334
- Figure 7-12 All APs Page 340
- Background Scanning Scenarios 344
- Channel 1 = 153 345
- Channel 2 = 161 345
- Routing Around Interference 346
- Authorizing Access Points 349
- Using DHCP Option 43 351
- • Type: 0xf1 (decimal 241) 352
- Lightweight Mode 356
- Local Core Files: 357
- Cisco Workgroup Bridges 359
- Guidelines for Using WGBs 360
- Sample WGB Configuration 362
- Figure 7-24 Clients Page 363
- Configuring Country Codes 367
- -U Regulatory Domain 373
- Guidelines for Migration 374
- Dynamic Frequency Selection 376
- Access Points 377
- Figure 7-30 Inventory Page 378
- Performing a Link Test 379
- Figure 7-32 Clients Page 380
- Figure 7-33 Link Test Page 381
- Configuring Flashing LEDs 384
- Viewing Clients 385
- Using the CLI to View Clients 388
- Configurations 391
- Upgrading Controller Software 392
- Downloading CA Certificates 400
- Uploading PACs 402
- Using the GUI to Upload PACs 403
- Using the CLI to Upload PACs 403
- Uploading Configuration Files 404
- Saving Configurations 408
- Resetting the Controller 409
- Managing User Accounts 411
- Creating Guest User Accounts 412
- Viewing Guest User Accounts 416
- Web Authentication Process 417
- Configuration Overview 434
- Configuration Guidelines 435
- Configuring Radio Resource 443
- Radio Resource Monitoring 444
- Dynamic Channel Assignment 445
- Overview of RF Groups 447
- Configuring an RF Group 448
- Viewing RF Group Status 450
- Figure 10-3 All APs Page 453
- Configuring Dynamic RRM 456
- Table 10-1 RRM Parameters 457
- Overriding Dynamic RRM 466
- Radio Measurement Requests 472
- Location Calibration 472
- Configuring Pico Cell Mode 476
- Overview of Mobility 484
- Overview of Mobility Groups 487
- Configuring Mobility Groups 490
- Prerequisites 491
- Running Mobility Ping Tests 508
- Overview of Hybrid REAP 510
- Hybrid REAP Guidelines 512
- Configuring Hybrid REAP 513
- Figure 12-6) 520
- Safety Considerations and 529
- Translated Safety Warnings 529
- Safety Considerations 530
- Warning Definition 530
- Varoitus 531
- Attention 531
- Avvertenza 531
- Advarsel 531
- ¡Advertencia! 532
- Varning! 532
- Class 1 Laser Product Warning 533
- Produto a laser de classe 1 534
- Klasse 1 laserprodukt 534
- Ground Conductor Warning 535
- Waarschuwing 546
- Controllers 551
- Information 555
- Statement 556
- Canadian Compliance Statement 557
- • Safety: EN 60950 558
- • Radio: EN 301.893 559
- Japanese Translation 560
- English Translation 560
- All Access Points 561
- End User License and Warranty 565
- End User License Agreement 566
- Limited Warranty 568
- Disclaimer of Warranty 570
- Additional Open Source Terms 571
- Troubleshooting 573
- Interpreting LEDs 574
- System Messages 574
- Monitoring Memory Leaks 582
- Diagnostic Channel 584
- Client Reporting 584
- Figure D-3) 591
- Using the Debug Facility 599
- Logical Connectivity Diagrams 605
- Cisco WiSM 606
- Controller Switch 608
- • debug wcp ? 609
- Numerics 611
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais