Cisco GoQAM Informações Técnicas Página 136
- Página / 308
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Cha
p
te
r
5 ICIM Mode Commands
112 4025561
Rev
A
ike
Syntax
ike ikeAction IpAddress
Description
The ike command is used to change the internet key exchange (IKE) settings.
Note: IPsec peers cannot be added or deleted through Telnet unless IPsec is enabled.
Parameters
The value of the ikeAction parameter can be either add to add an IPsec peer, or
delete to delete an IPsec peer. In either case, the parameter is followed by the
IpAddress of the peer. The IP address must be of the form 172.24.28.151.
When a peer is added, the CLI user will be prompted to enter a 16-character key. For
security reasons, you must enter this key twice, and it is not echoed to the screen. For
additional information on IPsec key requirements, see the IPsec section of the Prisma
II Enhanced Management System Guide, System Release 2.04, part number 4025559.
Access Rights Required
Admin
Example
The sample dialog below shows how this command would be used to add and then
delete an IPsec peer at IP address 192.25.64.101.
ICIM> ike add 192.25.64.101
please enter the key: [user enters key]
please re-enter the key: [user enters key]
SUCCESS!
ICIM> ike delete 192.25.64.101
SUCCESS!
ICIM>
Related Commands
show ike
show ipsec
- Prisma II EMS 1
- Remote User Interface 1
- Guide - System Release 2.04 1
- For Your Safety 3
- Notices 4
- Contents 5
- Contents 7
- Glossary 275 8
- Index 281 8
- Prisma II Product Notices 9
- Read and Retain Instructions 11
- Terminology 11
- Electric Shock Hazard 11
- Installation Site 12
- Installation Requirements 12
- Equipment Placement 12
- Ventilation 13
- Handling Precautions 14
- Grounding 14
- Equipotential Bonding 14
- Circuit Overload 15
- Electrostatic Discharge 16
- Fuse Replacement 16
- Batteries 16
- Modifications 17
- Accessories 17
- EMC Compliance Statements 18
- Laser Safety 19
- Warning Labels 21
- 23
- 1 Chapter 1 25
- Qualified Personnel 26
- Document Version 26
- Related Publications 27
- 1.01, part number 4015396 28
- What's New 29
- 2 Chapter 2 31
- Configuration 32
- User Authorization 33
- CLI Login and Logout 34
- CLI Command Modes 36
- CLI Command Modes 37
- Command Syntax 38
- Non-Modal Command Syntax 39
- Command Usage Guidelines 40
- Command Syntax 41
- General Hints and Help 42
- Alarm Information 43
- Getting Online Help 43
- 3 Chapter 3 45
- CLI> alarm 46
- No active alarms found 46
- CLI> 46
- clear 47
- CLI> date 48
- Tue, 3 Oct 2006 11:36:43 EST 48
- CLI> logout 52
- logout 53
- terminal 57
- CLI> who 58
- whoami 59
- 4 Chapter 4 61
- About Modspecs 65
- Notes on Usage 67
- 20/* MODULE> alarm 68
- 20/* MODULE> 68
- alarm domain 69
- 20/[5-7] MODULE> 70
- */* MODULE> logout 84
- reset 91
- Access Rights Required 100
- Example 100
- Related Commands 101
- Description 102
- Parameters 102
- Examples 102
- Transmitter (devtype: 1033) 105
- show module 115
- 5 Chapter 5 123
- In This Chapter 124
- Overview 125
- To Access ICIM Command Mode 126
- alarm 127
- ICIM> eventlogclear 128
- SUCCESS! 128
- ICIM> 128
- ICIM> logout 144
- C:\> 144
- manual 147
- ICIM> reboot 150
- show domain 159
- show eventlogall 161
- show file 163
- show iproute 165
- show traps 169
- traps 173
- Parameter Description 173
- ICIM> user delete smith8 178
- user unlock 179
- 6 Chapter 6 181
- TERMINAL> logout 191
- paging 195
- 7 Chapter 7 201
- Introduction 202
- Introduction 203
- Installation 204
- Web Browser Setup 205
- Login and Logout 207
- To Log Out 209
- To Change Login Defaults 209
- Using System View 211
- To View Module Summary 212
- To View Current Alarms 212
- Using System View 213
- Using ICIM Details 214
- To Work with ICIM Details 215
- Using Module Details 217
- To View Module Details 218
- To View Alarms 219
- To View Thresholds 219
- To View Controls 220
- To View Monitors 221
- Using System Settings 224
- Event Log Settings 225
- SNMP Traps 225
- Using the Event Log 227
- To Clear the Event Log 228
- User Management 229
- To Edit an Existing User 230
- To Review Current Users 231
- Web Interface Help 232
- To Use Navigate by Keywords 233
- 8 Chapter 8 235
- Obtaining Product Support 236
- Obtaining Product Support 237
- Return Product for Repair 238
- Return Product for Repair 239
- A Appx auto letter 245
- From CLI 246
- From ICIM 247
- Appendix A 252
- '?' 252
- From */* MODULE 253
- From TERMINAL 256
- B Appx auto letter 257
- ICIM Data 259
- Module Data 262
- Current Alarms 263
- Module Alarms 264
- Module Controls 265
- Module Monitors 266
- System Information 267
- C Appx auto letter 269
- In This Appendix 270
- Fan Tray 271
- Alarm Parameters 272
- Monitor Parameters 272
- Control Parameters 273
- Fan Tray Parameters (Split) 277
- 2 x 19 dBm Module 285
- 24 x 17.65 dBm Module 290
- Glossary 299
- Index 307
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais