Cisco ISE - Line Card ISE Manual do Utilizador descarregar pdf (Página 47)

Cisco IOSSoftware Configurationforthe Cisco12000Series One-PortChannelized OC-12/STM-4(DS1/E1)ISE Line

Verifying and Monitoring Configurations with Show Commands

Cisco IOS Release 12.0(27)S1

Discovering Current Status of the SONET Controller—show controllers sonet

To display information about the SONET port, including information on all of the configured channels,

use the following form of the show controllers sonet command:

show controllers sonet slot/port [brief | tabular]

When framing is SDH and AUG mapping is AU-4, the form of the show controllers command is as

follows:

show controllers sonet slot/port.au-4-number/tug-3-number/tug-2-number/e1-line-number [brief |

tabular]

When framing is SDH and AUG mapping is au-3, the form of the show controllers command is as

follows:

show controllers sonet slot/port.au-3-number/tug-2-number/t1-number [brief | tabular]

When framing is SONET and the mode is ct3, the form of the show controllers command is as follows:

show controllers sonet slot/port.sts1-number/t1-number [brief | tabular]

When framing is SONET and the mode is vt-15, the form of the show controllers command is as

follows:

show controllers sonet slot/port.sts1-number/vtg-number/t1-number [brief | tabular]

where:

• slot refers to the chassis slot where the 1-Port CHOC-12 ISE line card is installed.

• port refers to the physical port on the 1-Port CHOC-12 ISE line card and is always 0.

• au-4-number is always 1 for this line card.

• tug-3-number is a number in the range from 1 to 3.

• au-3-number is a number in the range from 1 to 12.

• tug-2-number is a number in the range from 1 to 7.

• e1-line-number is a number in the range from 1 to 3.

• t1-number is a number in the range from 1 to 4 (in ct3 mode, where a channelized T-3 is mapped

into the STS-1, t1-number is a number in the range from 1 to 28).

• sts1-number is a number in the range from 1 to 3.

• vtg-number is a number in the range from 1 to 7.

Router# show controllers sonet 2/0

SONET 2/0 is up. (Configured for Locally Looped) Hardware is GSR 1 port ISE OC12

(channelized)

STM1/OC3 (channelized)

Applique type is Channelized OCx interface

Clock Source is Line

Medium info:

Type: Sonet, Line Coding: NRZ, Line Type: IR SM

SECTION:

LOF = 9 LOS = 9 BIP(B1) = 79233

LINE:

AIS = 13 RDI = 6 REI = 711 BIP(B2) = 3921

Active Defects: SLOF SLOS LAIS

Active Alarms: SLOS

Alarm reporting enabled for: SF SLOS SLOF B1-TCA B2-TCA

BER thresholds: SF = 10e-3 SD = 10e-6

TCA thresholds: B1 = 10e-6 B2 = 10e-6 B3 = 10e-6

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 57 58

Comentários a estes Manuais

Sem comentários

Cisco ISE - Line Card ISE Manual do Utilizador Página 47

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Cisco ISE - Line Card ISE